ipw3945
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
ipw3945 [2007/12/29 20:22] – added link to iwlwifi thread darkaudax | ipw3945 [2008/06/28 13:45] – Remove the link to the iwlwifi injection thread in preparation of moving it to the iwl3945 article. (The link doesn't really belong here, as this is about the ieee80211 driver, while the thread deals with the mac80211 one.) netrolller3d | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== ipw3945 ====== | ====== ipw3945 ====== | ||
- | ===== Intel Pro/Wireless 3945 Injection Walkthrough ===== | + | //Note: This page is about the ipw3945/ |
- | I've tested this on Ubuntu 7.10 Gutsy and 7.04 Feisty but I don't see why it shouldn' | ||
- | To install ipwraw-ng, | ||
- | | + | ===== Intel PRO/ |
- | | + | |
- | | + | I've tested this on [[http:// |
+ | |||
+ | You need a Internet Connection with your LAN Cabel. | ||
+ | |||
+ | Open a Terminal and type... | ||
+ | |||
+ | **Pre requirements** | ||
+ | < | ||
+ | sudo apt-get install build-essential | ||
+ | sudo apt-get install libssl-dev | ||
+ | </ | ||
+ | |||
+ | // For openSUSE and other RPM-based distros, this is different (replace " | ||
+ | < | ||
+ | sudo zypper install gcc | ||
+ | sudo zypper install libopenssl-devel | ||
+ | </ | ||
+ | |||
+ | |||
+ | **Installation** | ||
+ | |||
+ | * Download ipwraw-ng from http:// | ||
+ | |||
+ | | ||
+ | |||
+ | | ||
< | < | ||
- | wget http://homepages.tu-darmstadt.de/ | + | wget http://dl.aircrack-ng.org/drivers/ |
tar -xjf ipwraw-ng* | tar -xjf ipwraw-ng* | ||
cd ipwraw-ng | cd ipwraw-ng | ||
Line 22: | Line 45: | ||
</ | </ | ||
- | To use ipwraw-ng, | + | **Use ipwraw-ng** |
- | | + | |
- | | + | |
- | The device created will automatically be in monitor mode. You can use iwconfig to set the channel and rate. | + | The device created will automatically be in monitor mode. |
< | < | ||
sudo modprobe -r ipw3945 | sudo modprobe -r ipw3945 | ||
sudo modprobe ipwraw | sudo modprobe ipwraw | ||
+ | </ | ||
+ | |||
+ | The new device name for injection should should be called wifi0 and the monitor interface should be rtap0. | ||
+ | |||
+ | < | ||
+ | lo no wireless extensions. | ||
+ | |||
+ | eth0 no wireless extensions. | ||
+ | |||
+ | wifi0 | ||
+ | Mode: | ||
+ | |||
+ | rtap0 no wireless extensions.</ | ||
+ | |||
+ | |||
+ | IMPORTANT before using airodump-ng you need to : | ||
+ | # ifconfig wifi0 up | ||
+ | |||
+ | **Configure your Wireless Card** | ||
+ | |||
+ | You can use iwconfig to set the channel and rate and transfer power. | ||
+ | |||
+ | < | ||
+ | iwconfig eth1 channel 11 (on which you want to sniff) | ||
+ | iwconfig eth1 rate 1M (min=1M and max=54M) | ||
+ | iwconfig eth1 txpower 16 (min=-12 and max=16) | ||
</ | </ | ||
Line 40: | Line 89: | ||
sudo modprobe ipw3945 | sudo modprobe ipw3945 | ||
</ | </ | ||
+ | |||
Line 48: | Line 98: | ||
Useful links: | Useful links: | ||
- | * Thread: [[http:// | ||
* Thread: [[http:// | * Thread: [[http:// | ||
* Thread: [[http:// | * Thread: [[http:// |
ipw3945.txt · Last modified: 2017/01/09 21:28 by mister_x