ipw3945
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
ipw3945 [2007/11/22 20:48] – kupesoft | ipw3945 [2008/06/28 14:04] – Fix a grammar mistake I made in my previous edit. netrolller3d | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== ipw3945 ====== | ====== ipw3945 ====== | ||
- | ===== Intel Pro/Wireless 3945 Injection Walkthrough ===== | + | //Note: This page is about the ipw3945/ |
- | I've tested this on Ubuntu 7.10 Gutsy and 7.04 Feisty but I don't see why it shouldn' | ||
- | To install ipwraw-ng, | ||
- | | + | |
- | | + | ===== Intel PRO/ |
- | | + | |
+ | I've tested this on [[http:// | ||
+ | |||
+ | You need a Internet Connection with your LAN Cabel. | ||
+ | |||
+ | Open a Terminal and type... | ||
+ | |||
+ | **Pre requirements** | ||
+ | < | ||
+ | sudo apt-get install build-essential | ||
+ | sudo apt-get install libssl-dev | ||
+ | </ | ||
+ | |||
+ | // For openSUSE and other RPM-based distros, this is different (replace " | ||
+ | < | ||
+ | sudo zypper install gcc | ||
+ | sudo zypper install libopenssl-devel | ||
+ | </ | ||
+ | |||
+ | |||
+ | **Installation** | ||
+ | |||
+ | * Download ipwraw-ng from http:// | ||
+ | |||
+ | | ||
+ | |||
+ | | ||
< | < | ||
- | wget http://homepages.tu-darmstadt.de/ | + | wget http://dl.aircrack-ng.org/drivers/ |
tar -xjf ipwraw-ng* | tar -xjf ipwraw-ng* | ||
cd ipwraw-ng | cd ipwraw-ng | ||
Line 22: | Line 46: | ||
</ | </ | ||
- | To use ipwraw-ng, | + | **Use ipwraw-ng** |
- | | + | |
- | | + | |
- | The device created will automatically be in monitor mode. You can use iwconfig to set the channel and rate. | + | The device created will automatically be in monitor mode. |
< | < | ||
sudo modprobe -r ipw3945 | sudo modprobe -r ipw3945 | ||
sudo modprobe ipwraw | sudo modprobe ipwraw | ||
+ | </ | ||
+ | |||
+ | The new device name for injection should should be called wifi0 and the monitor interface should be rtap0. | ||
+ | |||
+ | < | ||
+ | lo no wireless extensions. | ||
+ | |||
+ | eth0 no wireless extensions. | ||
+ | |||
+ | wifi0 | ||
+ | Mode: | ||
+ | |||
+ | rtap0 no wireless extensions.</ | ||
+ | |||
+ | |||
+ | IMPORTANT before using airodump-ng you need to : | ||
+ | # ifconfig wifi0 up | ||
+ | |||
+ | **Configure your Wireless Card** | ||
+ | |||
+ | You can use iwconfig to set the channel and rate and transfer power. | ||
+ | |||
+ | < | ||
+ | iwconfig eth1 channel 11 (on which you want to sniff) | ||
+ | iwconfig eth1 rate 1M (min=1M and max=54M) | ||
+ | iwconfig eth1 txpower 16 (min=-12 and max=16) | ||
</ | </ | ||
Line 40: | Line 90: | ||
sudo modprobe ipw3945 | sudo modprobe ipw3945 | ||
</ | </ | ||
+ | |||
+ | |||
===== Useful Links / Info ===== | ===== Useful Links / Info ===== |
ipw3945.txt · Last modified: 2017/01/09 21:28 by mister_x