ipw3945
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| ipw3945 [2007/08/28 23:17] – added wep cracking tutorial link darkaudax | ipw3945 [2017/01/09 21:28] (current) – Mark page as deprecated. mister_x | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== DEPRECATED ====== | ||
| + | |||
| + | **IMPORTANT NOTE**: This page is deprecated, updated documentation can be found [[install_drivers|here]] | ||
| + | |||
| ====== ipw3945 ====== | ====== ipw3945 ====== | ||
| - | At this point in time, this page is far from complete. | + | //Note: This page is about the ipw3945/ |
| + | |||
| + | ===== Injection Walkthrough ===== | ||
| + | |||
| + | This is for an intel PRO/ | ||
| + | |||
| + | I've tested this on [[http:// | ||
| + | |||
| + | You need a Internet Connection with your LAN Cabel. | ||
| + | |||
| + | Open a Terminal and type... | ||
| + | |||
| + | **Pre requirements** | ||
| + | < | ||
| + | sudo apt-get install build-essential | ||
| + | sudo apt-get install libssl-dev | ||
| + | </ | ||
| + | |||
| + | // For openSUSE and other RPM-based distros, this is different (replace " | ||
| + | < | ||
| + | sudo zypper install gcc | ||
| + | sudo zypper install libopenssl-devel | ||
| + | </ | ||
| + | |||
| + | |||
| + | **Installation** | ||
| + | |||
| + | * Download ipwraw-ng from http:// | ||
| + | |||
| + | * Install the modules and ucode | ||
| + | |||
| + | * Blacklist ipwraw (so it's not automatically loaded at boot time) | ||
| + | |||
| + | < | ||
| + | wget http:// | ||
| + | tar -xjf ipwraw-ng* | ||
| + | cd ipwraw-ng | ||
| + | make | ||
| + | sudo make install | ||
| + | sudo make install_ucode | ||
| + | echo " | ||
| + | sudo depmod -ae | ||
| + | </ | ||
| + | |||
| + | **Use ipwraw-ng** | ||
| + | |||
| + | * Unload the ipw3945 module | ||
| + | * Load ipwraw-ng | ||
| + | |||
| + | The device created will automatically be in monitor mode. | ||
| + | |||
| + | < | ||
| + | sudo modprobe -r ipw3945 | ||
| + | sudo modprobe ipwraw | ||
| + | </ | ||
| + | |||
| + | The new device name for injection should should be called wifi0 and the monitor interface should be rtap0. | ||
| + | |||
| + | < | ||
| + | lo no wireless extensions. | ||
| + | |||
| + | eth0 no wireless extensions. | ||
| + | |||
| + | wifi0 | ||
| + | Mode: | ||
| + | |||
| + | rtap0 no wireless extensions.</ | ||
| + | |||
| + | |||
| + | IMPORTANT before using airodump-ng you need to : | ||
| + | # ifconfig wifi0 up | ||
| + | |||
| + | **Configure your Wireless Card** | ||
| + | |||
| + | You can use iwconfig to set the channel and rate and transfer power. | ||
| + | |||
| + | < | ||
| + | iwconfig eth1 channel 11 (on which you want to sniff) | ||
| + | iwconfig eth1 rate 1M (min=1M and max=54M) | ||
| + | iwconfig eth1 txpower 16 (min=-12 and max=16) | ||
| + | </ | ||
| + | |||
| + | And when you're done, | ||
| + | |||
| + | < | ||
| + | sudo modprobe -r ipwraw | ||
| + | sudo modprobe ipw3945 | ||
| + | </ | ||
| + | |||
| + | ===== Useful Links / Info ===== | ||
| + | |||
| + | At this point in time, this page is far from complete. | ||
| Useful links: | Useful links: | ||
| - | * Thread: [[http:// | + | * Thread: [[http:// |
| - | * Thread: [[http:// | + | * Thread: [[http:// |
| - | * Thread: [[http:// | + | * Thread: [[http:// |
| - | * [[http:// | + | * [[http:// |
| * [[http:// | * [[http:// | ||
| + | |||
| + | Also consider using the [[links# | ||
ipw3945.1188335837.txt.gz · Last modified: by darkaudax
